BMW · 732 · Bar
Recommended bar for a BMW 732
- Drivetrain
- rear-wheel drive
- Body
- passenger car
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
bar
2.31 / 2.31
32-35 / 32-35 psi · 231 / 231 kPa
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
2.3 bar is not 23 psi. On this 732 2.2-2.4 bar converts to about 32-35 psi. Use the table, not a guess. Size estimates on this page include 195/65R15, 245/40R18 and 225/50R17 — interpolated from the catalogue midpoint, not a second factory sticker.
Bar, PSI and kPa
Bar-led conversions around the BMW 732. 2.2-2.4 bar is not “32-35 divided by ten”.
| Bar | PSI | kPa |
|---|---|---|
| 2.07 | 30 | 207 |
| 2.21 | 32 | 221 |
| 2.28 | 33 | 228 |
| 2.31 | 33.5 | 231 |
| 2.41 | 35 | 241 |
| 2.48 | 36 | 248 |
| 2.62 | 38 | 262 |
| 2.76 | 40 | 276 |
| 3.03 | 44 | 303 |
| 3.45 | 50 | 345 |
| 4.14 | 60 | 414 |
BMW 732 placard versus sidewall
If the BMW sticker is painted over, the handbook is next. This website is a map, not a replacement VIN label.
Estimated pressure by tyre size (195/65R15 and others)
195/65R15 is the first planning size here. 225/50R17 is usually the plus-size or LT step. Keep load index at or above original equipment.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 195/65R15 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Very common compact |
| 245/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Wide touring 18-inch |
| 225/50R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Touring 17-inch |
| 185/65R15 | 33 | 33 | 2.28 | 2.28 | 228 | 228 | Small / older car |
| 225/40R18 | 36 | 36 | 2.48 | 2.48 | 248 | 248 | Low-profile 18-inch |
| 205/55R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Typical mid-compact OEM |
| 225/45R17 | 35 | 35 | 2.41 | 2.41 | 241 | 241 | Sport 17-inch |
| 205/60R16 | 34 | 34 | 2.34 | 2.34 | 234 | 234 | Taller 16-inch |
Load notes
Load moves the rear of a passenger car first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 34 psi / 2.34 bar | 35 psi / 2.41 bar |
| Motorway + luggage | 35 psi / 2.41 bar | 38 psi / 2.62 bar |
How to set the 732
- Park the BMW 732 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a rear-wheel drive 732 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this 732.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
BMW notes
BMW run-flats still want the placard. Comfort settings in the iDrive do not replace the door-pillar figure on this 732.
Spare and inflator kit
A matching full-size spare on the BMW 732 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the BMW sticker and this page disagree, the sticker wins.
Other BMW models
Questions about this 732
What is that in bar and kPa for the 732?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
Front versus rear on the BMW 732?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
Should I bleed pressure after a motorway run?
No. Heat raises the gauge. Set cold only. Bleeding a hot tyre leaves it low the next morning.
What tyre pressure should a BMW 732 use?
Catalogue reference is 32-35 psi front and 32-35 psi rear (2.2-2.4 / 2.2-2.4 bar), cold. Confirm on the door-pillar placard.
Is the sidewall number correct on a BMW 732?
No. Sidewall PSI is a maximum. The 732 placard is the operating target, near 32-35/32-35 psi.
Handbook: placard · bar vs PSI · front vs rear · cold inflation