BAIC · Beijing X35 · Rear
BAIC Beijing X35 rear tyre pressure
- Drivetrain
- front-wheel drive
- Body
- SUV / crossover
- PSI F / R
- 32-35 / 32-35
- Bar F / R
- 2.2-2.4 / 2.2-2.4
psi rear
34
2.31 bar · 231 kPa at the rear axle
32-35 psi F · 32-35 psi R · 2.2-2.4 / 2.2-2.4 bar · 231/231 kPa
Loaded Beijing X35 rears often need the sticker’s second column, not a copy of the front 32-35 psi figure. A 10 °C overnight drop takes roughly 1 psi (0.07 bar) off a closed BAIC tyre.
BAIC Beijing X35 placard versus sidewall
Sidewall PSI is a carcass maximum. Recommended operating pressure for this Beijing X35 is the pillar sticker, near 34/34 psi.
Estimated pressure by tyre size (245/55R19 and others)
245/55R19 is the first planning size here. 225/60R18 is usually the plus-size or LT step. Keep load index at or above original equipment.
| Tyre size | Front PSI | Rear PSI | Front bar | Rear bar | Front kPa | Rear kPa | Note |
|---|---|---|---|---|---|---|---|
| 245/55R19 | — | 36 | — | 2.48 | — | 248 | Low-profile 19-inch |
| 245/60R18 | — | 37 | — | 2.55 | — | 255 | Heavier CUV |
| 225/60R18 | — | 35 | — | 2.41 | — | 241 | Highway CUV |
| 235/60R18 | — | 36 | — | 2.48 | — | 248 | Plus-size 18-inch |
| 215/70R16 | — | 34 | — | 2.34 | — | 234 | Compact crossover |
| 235/65R17 | — | 36 | — | 2.48 | — | 248 | Mid-size SUV |
| 225/65R17 | — | 35 | — | 2.41 | — | 241 | Very common 17-inch |
| 255/50R20 | — | 37 | — | 2.55 | — | 255 | 20-inch plus-size |
Pressure against load
Load moves the rear of a SUV / crossover first. If the factory placard already has a “laden” column, use that instead of these sketches.
| Condition | Front (est.) | Rear (est.) |
|---|---|---|
| Driver only | 34 psi / 2.34 bar | 34 psi / 2.34 bar |
| Full occupancy | 35 psi / 2.41 bar | 36 psi / 2.48 bar |
| Motorway + luggage | 36 psi / 2.48 bar | 38 psi / 2.62 bar |
A family SUV / crossover with a boot full of luggage should use the laden rear figure if Ford, VW or Mercedes printed one. Otherwise the modest steps in the load table are only a sketch for this Beijing X35.
How to set the Beijing X35
- Park the BAIC Beijing X35 for at least three hours (cold tyres).
- Use a calibrated gauge, not the only meter on a forecourt hose.
- Set the placard for that axle — about 32-35 psi / 2.2-2.4 bar front and 32-35 psi / 2.2-2.4 bar rear on this catalogue row.
- Recheck all four. A 2 psi miss on a front-wheel drive Beijing X35 is enough to feel a pull.
- Refit valve caps and reset TPMS if the handbook asks for a relearn.
PSI, bar and kPa
PSI-led conversions for the BAIC Beijing X35 band (32-35 / 32-35).
| PSI | Bar | kPa |
|---|---|---|
| 30 | 2.07 | 207 |
| 32 | 2.21 | 221 |
| 33 | 2.28 | 228 |
| 33.5 | 2.31 | 231 |
| 35 | 2.41 | 241 |
| 36 | 2.48 | 248 |
| 38 | 2.62 | 262 |
| 40 | 2.76 | 276 |
| 44 | 3.03 | 303 |
| 50 | 3.45 | 345 |
| 60 | 4.14 | 414 |
Temperature drift
Roughly 1 psi per 5–6 °C. The table uses 34 psi as a 20 °C baseline for this Beijing X35.
| Ambient | Gauge (front mid) | Bar | kPa | Note |
|---|---|---|---|---|
| −5 °C (hard frost) | 31 psi | 2.14 bar | 214 kPa | Gauge reads low; do not overfill once warm |
| 0 °C | 32 psi | 2.21 bar | 221 kPa | Gauge reads low; do not overfill once warm |
| 8 °C (UK winter morning) | 33 psi | 2.28 bar | 228 kPa | Gauge reads low; do not overfill once warm |
| 20 °C (set cold here) | 34 psi | 2.34 bar | 234 kPa | Baseline |
| 30 °C | 36 psi | 2.48 bar | 248 kPa | Do not bleed a hot tyre |
| 38 °C (heatwave tarmac) | 37 psi | 2.55 bar | 255 kPa | Do not bleed a hot tyre |
BAIC notes
No special BAIC exception: the Beijing X35 uses the door-pillar placard. Size estimates on this page only help if you have left the original load index behind.
Spare and inflator kit
A matching full-size spare on the BAIC Beijing X35 usually follows the higher axle (often the rear, near 32-35 psi). A space-saver is commonly 60 psi / 4.1 bar — read that tyre’s own sidewall. An inflator kit is not a spare; check the sealant date.
If the BAIC sticker and this page disagree, the sticker wins.
Other BAIC models
Questions about this Beijing X35
Front versus rear on the BAIC Beijing X35?
This row is 32-35 F / 32-35 R. Even when they match, a laden rear can justify a higher number if the sticker prints one.
How often should I check a Beijing X35?
Monthly, before a long trip, and after a 10 °C weather swing. Include a full-size spare.
Is the sidewall number correct on a BAIC Beijing X35?
No. Sidewall PSI is a maximum. The Beijing X35 placard is the operating target, near 32-35/32-35 psi.
What is that in bar and kPa for the Beijing X35?
Mid-points are about 2.31 bar (231 kPa) front and 2.31 bar (231 kPa) rear.
What PSI if I plus-size toward 225/60R18?
Keep load index at or above OEM. Low-profile sizes usually stay at or slightly above the placard. Use 245/55R19, 245/60R18 and 225/60R18 as a planning band.
Handbook: placard · bar vs PSI · front vs rear · cold inflation